Monday 8 December 2014

Spirit of Air-o-bian

Some time ago, I wrote about my plans to recreate the Air-o-bian kite from the 1930s. If you've been following me on Facebook, you'll know this project has been progressing steadily. I guess it's time now to tell you the full story.

Stage 1 of the project was to try and recreate an Air-o-bian kite as close as possible to the original patent:


To achieve that, I got myself a pair of Spirit of Air box kites (the idea was to end up with a pair of Air-o-bians, so we could fly them as Flying Fish). I created a rudder from a plastic storage box, and mounted that on a 5.5mm carbon tube, inside which was a 3mm carbon rod.




















Note that, according to the patent, the rudder is not connected to the bridle lines, but is connected to the upright spars with a piece of elastic. Kite was bridled, and we were ready for the first test flight!


So did the Air-o-bian fly? Yep, no problem at all. Did it steer as it was meant to? Nope ...


The rudder basically didn't do anything, and any attempt at pulling one line or the other merely resulted in the kite rotating around its longitudinal axis, but not moving into the direction of the pulled line.

To be perfectly honest, I would have been surprised to see the kite steer, as the rudder wasn't controlled by the bridle lines, or by anything else for that matter! So on to stage 2 ...

For stage 2, I decided to move away from the original patent, and link the bridle lines directly to the rudder. This way, the rudder would move as the lines were being pulled. I decided to use the second box kite I had for this, and leave the other kite as it was. If it worked, I could simply adapt that one.


Test flight number 2 showed this direct rudder control had no effect whatsoever! It still was the case that pulling on either line resulted in the kite rotating rather than steering in a particular direction.

Now I was still following the patent regarding the attachment points of the 'uphaul' part of the bridle, i.e. on the lateral upright spars as you face the kite. What about making the two 'uphauls' attach together on the flyer-facing upright spar? I know I'm moving further and further from the patent, but I just wanted the box kite to steer ...

So here's what the improved bridling looks like. At the lower (rudder) end of the kite, the bridle lines connect directly to the two sides of the rudder; pulling on one line will make the rudder go one way, pull on the other, and it goes the other way.


And at the top end of the kite, the two 'uphauls' come together on a single spar; that ought to reduce the rotation of the kite, as all pulling will now only go to the rudder.


Test flight number 3! Will it steer now?


Well, yes, actually! After getting used to the kite flying to and fro a lot, I actually managed to fly it into loops left and right!


It turned out that the position of the tow point was pretty crucial. Too low down, and the kite wouldn't have enough angle to fly; too high up, and the bridle lines connected to the rudder would remain slack, and it wouldn't steer at all. But a bit of trial and error seemed to give me the sweet spot.

Even though I managed to steer the kite in the end, control is not even close to what we would need to fly two of them side-by-side, so it'll remain a one-off for now (unless I get a sudden brainwave as to how to improve control massively).

So here's our "Spirit of Air-o-bian"! The name is a nod to the maker of the original box kite, and to the fact that that the end result has the 'spirit' of the original Air-o-bian in it, even though I've veered further and further away from the patent. It definitely was a fun experiment!

2 comments:

  1. Would you not get more responsive steering with the rudder entirely inside the box?

    ReplyDelete
    Replies
    1. Interesting idea! Haven't tried it, so can't say yes or no. It would take the kite even further away from the original patent, but I may try it out one day.

      Delete